Voir le texte source

Tile over tile means just what it says, in this case youre likely to sandwich a layer of radiant heating mats between the old and the brand new tile. Tile over tile is an simple way of preventing the mess related to getting up the old bath-room floor, but requires thorough planning. Deflection:  [http://amazingrenovationsinc.com/repair/mold-removal.html mold remediation houston]  Before you install a radiant heat mat over the old bath-room tile and install new tile over the mat, you should check always the ground for deflection. This is actually the maximum amount the ground can go beneath the anticipated weight (you). Ceramic tile is hard and will break o-r dislodge if the surface bends underneath the load. Heres an easy test: Stay in the centre of the bath-room floor and jump up and down. If the floor moves it's a deflection problem and isn't a great choice for tile over tile installation until you reinforce the sub-floor. Prevent That Sinking Feeling: Since youre tiling over tile, you should prepare beforehand in order to avoid making the bathtub, toilet and vanity appear to be theyre sinking to the new floor. Luckily, lots of the new glorious warming pads are no heavier than the degree of the mortar you'd normally submit an application for many tile installations. Combine this with the most elevation above the old floor and a hardwood depth of inch will be only inch. One method to keep the bath-room fixtures from looking swallowed up by the new floor would be to remove and reinstall the baseboard. Even better, you will want to get new baseboard tile to complement the new ground?  [http://amazingrenovationsinc.com/roofing.html roofing contractor houston]  The height of-the new floor may also require you to change the length of the s) and perhaps put in a new tolerance. Preparation: Eliminate o-r re-attach broken tile pieces. If you remove them, wait until the ground has been sanded and carefully vacuumed before you fill the places with mortar. If any of the tiles have checks broader than 1/8, you should think about a crack isolation membrane. This membrane is a roll-on product that you apply to the old tile. The new floor is allowed by the membrane to move independently of the old. Next, sand the old tile and so the mortar features a good bonding surface. A consistent bonding surface would be ensured by a belt sander. Please make sure you wear a breathing apparatus and safety glasses while sanding. The tiles may have been shot with toxic lead glaze. After sanding, machine the tile and wipe down with an all-purpose cleaner. Pay special attention to the areas untouched from the sander. Installation:  [http://amazingrenovationsinc.com/renovations-remodeling/fence-installations.html fencing houston]  Roll-out the mats pre-fabricated to your specifications from the producer. Some sparkling systems, like Quickmat, are self-adhesive and need no mortar to secure them to the old hardwood floor. Keep a board and some scrap 2 x 4s practical once the bathroom will be used to protect the mats, if youre re-tiling the only real bathroom. Throughout the installation process, make use of a electronic ohm meter to test the resistance of the heat rugs. This may help you check the mats for short-circuits. Have your electrician connect the heat pads to-the power source and install the thermostat. Depending on the local electrical assessment processes, you might have to wait until the work is inspected before you start laying tile. Trowel out-the mortar over the pads. Some manufacturers recommend latex- altered o-r grout and epoxy-modified mortar instead of water-based multi-purpose adhesives. Mortar beds thicker than 3/8 inch should work fine for some systems; they simply take somewhat longer to warm up. Since you wont be within the entire floor with heat mats, be sure the mortar applied over open areas, (under the bathroom) is level with the mortar lined mats.  [http://amazingrenovationsinc.com/outdoor/kitchens.html outdoor kitchen houston]  Dont return the trowel around the pad or heating cable to eliminate excess mortar from the trowel. This may sever the heating cable. At this point, you would lay the tile. Practice on your neighbors bathroom floor, when you yourself have no knowledge tiling. Fire It Up! Your glowing heated bath-room ground seems wonderful and you cant wait to get warm feet. Proceed, but only for 10 minutes. Dont set the machine in to full operation until the mortar is entirely healed. This can just take as much as a month. See why extensive planning is really essential?